HardTrack Mobile
HardTrack Mobile/Desktop on Windows Tablet - Best Practices
Equipment Overview Wireless Reader - Remove the reader from the small Pelican case and charge it as soon as possible. Note: The reader will slowly charge while in use when it is attached to the Rugged Tablet's USB port Use the supplied USB cable and ...
HardTrack Mobile - Quick Start using Only the Handheld - Best Practices
Best Practices for setting up and monitoring concrete pours only using the handheld. Rather than setting up your concrete placements using HardTrack on your PC, you can use the handheld device to perform all of the necessary setup and monitoring ...
How to Fix Windows Mobile Device Center
You will need Windows Administrative Authority to complete these tasks. Starting with HardTrack Desktop version 5.1._02.31 or greater: Typically after a Windows Update, the Windows Mobile Device Center will need to be updated for the connection ...
How to Locate a Lost Tag using the Handheld Device
HardTrack has a built in feature to assist you with locating lost Tags. It works using the concept of a Giger counter. The closer you move towards a tag you are attempting to locate, the stronger the RF signal between the handheld that the tag will ...
How to Upload a Project from the Handheld and Generate a Report - Best Practices
When the time comes to generate a report from an already logging project on the handheld device, please follow these instructions. Read the sensors/tags by doing the following: - open the project on the handheld - single click on one of the ...
How to set up a new HardTrack Mobile Concrete Pour - Best Practices
Starting with version 4.0._01.17 of HardTrack Mobile, this is the best procedure to follow to set up a new HardTrack Project and Start the Sensors/Tags Logging. You can check the version of HardTrack Mobile running on your handheld device, by double ...
Initialize the Tags and Start logging on all Tags for a Project - Best Practices
These instructions explain the fastest way to initialize all of the tags for a project and how to start logging on all of them quickly so that when you run your reports, the date-time stamps on the temperature data from each tag is as close as ...
How to Reset the Handheld Device
To perform a warm reset: • Press the FN/BLUE key and the ENTER key simultaneously for a few seconds. During a warm reset, running programs are halted. The contents of RAM, flash memory and the registry are preserved To perform a cold reset: If the ...
How to work with all the Tags/Loggers in a Pour/Project at the Same Time
Initialize all the tags for your project After either adding Known Tags or Scanning for Tags and you have saved your project, you can Initialize all the tags for your project by clicking on Tag, Reuse Tag(s), Reuse All Tags. Remember you have to ...
How to Install HardTrack Desktop on a new PC for use with HardTrack Mobile
To install or upgrade HardTrack, you will need to have Administrator authority on your PC. You will receive a link in an email message that will take you to Dropbox so you can download the HardTrack Desktop Installation files. - Don't worry about ...
How to Use a Backup Log File to Generate a Report
This is how we can temporarily restore the backup log file, use it to generate a report, and then return the current live data back in place. The backed of the file is stored in the sub-directory \Backup on the Flash Drive of the Handheld Look ...
HardTrack Mobile User Manual
HardTrack Mobile User Manual Revision 5.1 April 21, 2021 For further information or assistance, call WAKE's Customer Service Hotline Toll-Free at US (800) 957-5606 or CA: (647) 931-6995 Wake, Inc. reserves the right to alter any of its products or ...
How to Configure HardTrack Desktop for use with a Mobile Reader
HardTrack may have been pre-installed onto a Windows device supplied by Wake with your order. If not, a copy of the HardTrack Install files can be located on the USB drive shipped in the box with your Bluetooth Reader. If HardTrack was pre-installed ...
How to update HardTrack Mobile on a Handheld Device to a new version using HardTrack Desktop
How to update HardTrack Mobile on a Handheld Device to a new version 1) Update your HardTrack Desktop application 2) Place your Mobile Device in the Docking Station and attach the USB cable so that the Mobile Device can communicate with your PC which ...
How to share a HardTrack Temperature Report with your Associates
Features are available in HardTrack that may assist you in communicating with your associates and project owners. When you Import your HardTrack Mobile projects into HardTrack Desktop, your projects will are automatically published into a secure ...
Windows Mobile Device Center Installation
You will need Windows Administrative Authority to complete these tasks. Starting with HardTrack Desktop version 5.1._02.31 or greater: After successfully installing HardTrack Desktop and applying any Updates to HardTrack Desktop, click on Project, ...
How to set time zone, date & time and Taskbar settings for HardTrack Mobile on the Handheld
On the handheld device, please do the following: Click on Settings, Control Panel: Click in Date & Time: Select your Time Zone and check the Automatically adjust clock for daylight savings if it applies: You can click directly into the Year and type ...
How to get Device Mirror working between HardTrack Desktop and HardTrack Mobile running on a Handheld Computer
After following the instructions in the HardTrack users manual, you cannot get Device Mirror to run correctly on your PC, this article may assist you in resolving the issue. Device Mirror will need to be initially installed. This is usually taken ...
Bluetooth Reader not Connecting to HardTrack running on Tablet
How to Restart the i-PORT Bluetooth Reader Connect the USB Charging Cable to the i-PORT Bluetooth Reader and connect the other end to a PC. This will reset the Reader